CC300M Masonry Saw: Complete Guide to Specifications, Cutting Capacity, Blades, Uses, and Maintenance

The CC300M masonry saw is a compact electric masonry saw designed for cutting brick, block, pavers, stone, and other masonry materials. Manufactured by Diamond Products under its Core Cut equipment line, the CC300M is built for contractors who need a portable saw that offers more control and cutting depth than a handheld saw while remaining easier to transport than a large commercial block saw.

The CC300M uses a 14-inch blade, provides a maximum cutting depth of 5 inches, and is powered by a 2-horsepower electric motor. The current manufacturer specification lists a 115-volt, 15-amp electrical system operating at 3,600 RPM. It also features a smooth sliding material table and a cutting head that is pulled downward into the material.

For masons, hardscape installers, landscapers, general contractors, rental companies, and homeowners completing larger masonry projects, the CC300M offers a practical combination of portability, cutting capacity, and straightforward electric operation.

What Is the CC300M Masonry Saw?

The CC300M is a stationary masonry cutting saw that holds the material on a sliding table while the operator brings the blade into the workpiece.

It is designed primarily for cutting materials such as:

• Concrete pavers

• Clay brick

• Concrete brick

• Concrete block

• Masonry units

• Landscape block

• Natural stone

• Retaining-wall products

• Thin precast concrete materials

The exact blade should always be selected according to the material.

Instead of carrying the saw through the cut as with a handheld power cutter, the operator places the material on the CC300M table and guides it through the blade. This helps create repeatable straight cuts and improves control when cutting multiple pieces.

CC300M Masonry Saw Specifications

Current Diamond Products specifications for the CC300M include:

Blade capacity: 14 inches

Maximum cutting depth: 5 inches

Maximum cutting length: 16 inches

Material capacity: 8 x 8 x 16 inches

Motor: 2 HP electric

Power supply: 115V / 60 Hz

Amp draw: 15 amps

Blade speed: 3,600 RPM

Saw height: 24 inches without stand

Saw length: 28 inches

Saw width: 23 inches

Weight: 85 pounds

Part number: 5800730

Catalog number: 84807

These are the current manufacturer-listed specifications for the CC300M.

What Size Blade Does the CC300M Use?

The CC300M accepts a maximum 14-inch masonry blade.

A 14-inch diamond blade gives the saw its maximum 5-inch cutting depth.

When choosing a replacement blade, consider:

• Blade diameter

• Arbor size

• Maximum RPM

• Wet or dry rating

• Material compatibility

• Segment design

• Bond hardness

A blade that physically fits the saw is not automatically appropriate for every material.

How Deep Does the CC300M Cut?

The CC300M has a maximum cutting depth of 5 inches with a 14-inch blade.

This gives it enough capacity for many common masonry materials, including:

• Standard concrete pavers

• Thick hardscape pavers

• Brick

• Landscape blocks

• Masonry units

• Selected wall caps

• Stone products

The 5-inch depth is especially useful for contractors working with thicker products that cannot be cut completely with smaller tile saws.

Maximum Material Capacity

Diamond Products lists the CC300M with a maximum material capacity of 8 inches x 8 inches x 16 inches and a maximum cut length of 16 inches.

This makes the saw useful for common brick and block dimensions while keeping the overall machine compact.

Always make sure the material:

• Fits securely on the table

• Remains supported throughout the cut

• Does not interfere with the blade guard

• Can move freely along the sliding table

Trying to force oversized material through the saw may create unstable cutting conditions.

2 HP Electric Motor

The CC300M is powered by a 2-horsepower electric motor running on standard 115-volt, 60-Hz power and drawing approximately 15 amps.

Electric power provides several advantages.

There is:

• No gasoline to mix or store

• No engine oil changes

• No carburetor

• No exhaust

• Easier starting

• Lower engine-related maintenance

This makes the CC300M practical for shops, covered work areas, remodeling jobs, and locations where gasoline-powered equipment would be inconvenient.

Adequate electrical power is still essential. Undersized extension cords or weak circuits can reduce motor voltage and cause overheating.

3,600 RPM Blade Speed

The CC300M operates at a listed blade speed of 3,600 RPM.

Any diamond blade installed on the saw must have a maximum RPM rating equal to or greater than the machine's operating speed.

Never use a blade with:

• Unknown RPM rating

• Cracked core

• Missing segments

• Damaged arbor

• Excessive warping

Blade speed is a critical safety specification, not simply a performance measurement.

Smooth Sliding Material Table

One of the CC300M's key features is its smooth sliding material cutting table.

The table allows the material to move through the blade in a controlled path rather than requiring the operator to hold a heavy block freehand.

Benefits include:

• Straighter cuts

• Better repeatability

• Increased material support

• More consistent feed speed

• Reduced operator effort

The table should move smoothly without excessive side-to-side movement.

If travel becomes rough, inspect the rollers, tracks, bearings, and accumulated masonry debris.

Pull-Down Cutting Head

The CC300M uses a cutting head that is pulled down into the material.

This design allows the operator to control blade engagement instead of pushing a fixed blade through the entire piece at once.

A pull-down head is useful for:

• Controlled entry into thick material

• Partial-depth cuts

• Repeated cuts

• Larger blocks

• Better visibility of the cutting area

Do not force the cutting head downward.

Allow the diamond blade to grind through the material at a controlled rate.

Tool-Free Air Filter Replacement

The CC300M incorporates a foam air-filter system around its electric motor, and Diamond Products highlights tool-free air filter replacement as a key feature. The saw also ships with two spare air filters according to the current product listing.

Masonry cutting creates significant abrasive dust.

An effective air filter helps protect the electric motor from:

• Concrete dust

• Brick particles

• Stone dust

• Fine abrasive debris

A clogged filter can reduce motor cooling and contribute to overheating.

Inspect the filter regularly during dusty work.

CC300M for Cutting Brick

Brick is one of the ideal materials for the CC300M.

The saw can be used for:

• Brick walls

• Garden borders

• Walkways

• Fireplaces

• Columns

• Veneer work

• Decorative masonry

A masonry diamond blade designed for brick will generally provide good production and blade life.

For finished exposed edges, a smoother-cutting blade may be preferred.

CC300M for Cutting Concrete Block

The CC300M can also handle concrete masonry units within its material capacity.

Applications may include:

• Wall construction

• Retaining structures

• Landscape walls

• Openings

• Block fitting

• Utility penetrations

Concrete block can be abrasive, so use a blade formulated for block or masonry.

A blade designed exclusively for very hard concrete may not provide ideal life in abrasive block.

CC300M for Pavers

Hardscape contractors may use the CC300M for cutting concrete and clay pavers.

Typical paver applications include:

• Patio borders

• Driveway edges

• Walkways

• Fire pits

• Outdoor kitchens

• Pool decks

• Retaining-wall caps

• Landscape transitions

The sliding table makes repetitive paver cuts easier to control.

For highly visible decorative pavers, blade selection becomes especially important because an aggressive segmented blade may create a rougher finished edge.

Can the CC300M Cut Natural Stone?

Yes, depending on stone thickness and the installed diamond blade.

Possible materials include:

• Limestone

• Sandstone

• Bluestone

• Travertine

• Selected granite products

Natural stone varies widely in hardness.

A blade designed for abrasive sandstone may be very different from one intended for hard granite.

Always select the diamond blade based on the specific stone.

Segmented Diamond Blade for the CC300M

A segmented masonry blade is commonly used when production speed is the priority.

Segmented blades provide:

• Fast material removal

• Good debris clearance

• Effective cooling

• Strong performance in brick and block

They are useful for general construction cuts where a perfectly polished edge is not necessary.

Turbo Diamond Blade

A turbo blade offers a compromise between speed and finish quality.

It may be useful for:

• Concrete pavers

• Natural stone

• Dense masonry

• Decorative hardscape materials

Turbo blades generally produce a smoother cut than aggressively segmented masonry blades while maintaining good cutting speed.

Continuous-Rim Blade

Continuous-rim blades are typically associated with tile and delicate finish materials.

They may provide cleaner edges but usually cut more slowly and may not be appropriate for thick, highly abrasive masonry.

Always use a blade designed for the exact material and saw.

Wet Cutting With the CC300M

Depending on the CC300M setup and accessories, water can be used to improve masonry cutting.

Wet cutting can help:

• Reduce airborne dust

• Cool the blade

• Remove cutting debris

• Improve blade life

• Reduce heat buildup

Water also creates slurry.

The work area should be arranged so slurry does not create electrical hazards or accumulate around the motor.

Use only manufacturer-approved wet-cutting accessories and follow the saw's operating manual.

Dry Cutting Considerations

If the installed blade and saw configuration permit dry operation, additional dust-control precautions may be required.

Masonry materials can contain crystalline silica.

Dry cutting may produce large quantities of respirable dust.

Appropriate dust collection, ventilation, and respiratory protection should be used according to the application and applicable safety requirements.

Electrical Requirements

The current CC300M runs on a standard 115-volt, 15-amp circuit.

However, the electrical supply should be capable of supporting the machine under full load.

Avoid:

• Excessively long extension cords

• Undersized wire gauge

• Damaged cords

• Loose outlets

• Shared overloaded circuits

Voltage drop can cause:

• Slow blade speed

• Reduced cutting power

• Motor overheating

• Circuit breaker trips

Use extension cords sized according to the manufacturer's recommendations.

CC300M Weight and Portability

The saw weighs approximately 85 pounds, according to the current manufacturer listing.

This is relatively lightweight for a 14-inch masonry saw.

Its compact dimensions of approximately 28 inches long by 23 inches wide make it practical for:

• Work vans

• Pickup trucks

• Trailers

• Rental fleets

• Small workshops

Use proper lifting techniques or mechanical assistance when moving the machine.

CC300M Maintenance

Routine maintenance should include:

• Cleaning masonry dust

• Cleaning slurry

• Inspecting the blade

• Inspecting the blade guard

• Checking the electric cable

• Cleaning or replacing the air filter

• Inspecting table movement

• Checking fasteners

• Cleaning blade flanges

• Inspecting the motor

Diamond Products provides a dedicated CC300M Series owner's manual and parts documentation for the machine.

Blade Inspection

Before every cutting session, check the blade for:

• Missing segments

• Cracks

• Warping

• Arbor damage

• Excessive wear

• Uneven segment wear

A damaged blade should be removed from service immediately.

Cleaning the Saw

Masonry dust should not be allowed to accumulate around the motor, sliding table, blade guard, or air intake.

After use:

1. Disconnect electrical power.

2. Allow the blade to stop completely.

3. Remove loose debris.

4. Clean the material table.

5. Inspect the blade.

6. Clean the air-filter area.

7. Remove slurry if wet cutting was used.

8. Allow components to dry before storage.

Never clean the saw while it remains connected to electrical power.

Common CC300M Problems

Saw Has Low Cutting Power

Possible causes include:

• Dull blade

• Incorrect blade

• Low voltage

• Undersized extension cord

• Excessive feed pressure

• Dirty motor filter

Blade Cuts Slowly

Possible causes include:

• Glazed blade

• Wrong bond

• Hard material

• Dull diamonds

• Excessive cutting depth

Table Does Not Slide Smoothly

Check:

• Tracks

• Rollers

• Bearings

• Masonry debris

• Bent components

Circuit Breaker Trips

Possible causes include:

• Overloaded electrical circuit

• Excessive cutting pressure

• Damaged cable

• Motor problems

• Incorrect extension cord

Stop operating the saw until the cause is determined.

Frequently Asked Questions About the CC300M Masonry Saw

What is the CC300M masonry saw?

The CC300M is a compact electric masonry saw manufactured by Diamond Products for cutting brick, block, pavers, stone, and similar materials.

What size blade does the CC300M use?

It accepts a maximum 14-inch blade.

How deep does the CC300M cut?

It provides a maximum cutting depth of 5 inches with a 14-inch blade.

How long of a cut can it make?

Diamond Products lists a maximum cutting length of 16 inches.

What is the material capacity?

The listed maximum capacity is 8 x 8 x 16 inches.

How much horsepower does the CC300M have?

The current manufacturer specification lists a 2 HP electric motor.

What voltage does it use?

The current CC300M operates on 115V/60Hz power.

How many amps does the CC300M draw?

The current manufacturer specification lists a 15-amp draw.

What RPM does the blade run?

The listed blade speed is 3,600 RPM.

How much does the CC300M weigh?

The current listed product weight is approximately 85 pounds.

Can the CC300M cut brick?

Yes. Brick cutting is one of its primary applications.

Can the CC300M cut concrete block?

Yes, when the material fits within the saw's capacity and the correct masonry blade is installed.

Can the CC300M cut pavers?

Yes. It is useful for cutting concrete and clay pavers used in patios, driveways, walkways, and other hardscape projects.

Can it cut stone?

Yes, with the correct diamond blade and provided the stone dimensions remain within the saw's capacity.

Does the CC300M use a sliding table?

Yes. Diamond Products lists a smooth sliding material cutting table as a key feature.

Does the cutting head move?

Yes. The cutting head is pulled downward into the material during cutting.

Does the CC300M have an air filter?

Yes. It uses a foam air-filter system with tool-free replacement, and the current listing states that two spare filters are included.

Is a blade included with the saw?

The current Diamond Products listing specifically states that the blade is not included.

What blade should I buy for the CC300M?

Choose a 14-inch or smaller compatible masonry diamond blade matched to the material, arbor, RPM, and wet or dry cutting requirements.

Is the CC300M good for professional contractors?

Yes. Its 14-inch blade capacity, 5-inch cutting depth, 2 HP electric motor, sliding table, and relatively lightweight 85-pound frame make it a practical option for masons, hardscape installers, contractors, and rental fleets that need a compact masonry saw.